The Laser
Cutters and Plotters
Vinyl cutters and pen plotters: HPGL cutters by serial port, network or USB, Silhouette Cameo and Portrait over USB, Brother ScanNCut by FCM file, with blade offset and overcut.
Experimental: written from the description of the HPGL and GPGL (Silhouette) languages and tried on simulated cutters, not yet on a real machine.
Bernie also drives cutters (adhesive vinyl, heat transfer vinyl, paper) and pen plotters, with no internet connection.
- Creating the device: Bernie tour or Add a Laser… › Cutter / plotter. At “Your machine”, Controller: HPGL cutter (serial port) for most vinyl cutters, Silhouette (USB: Cameo, Portrait), or GRBL machine (knife or pen) for a plotter or a self-built machine; work area (cutter width × material length) and origin, most often bottom left. The Starter — cutter library (adhesive vinyl, heat transfer vinyl, paper, cardstock…) gives starting speeds, and the example project is a sticker.
- Knife tool (device settings): the blade tip is offset from the holder’s axis. Blade offset (about 0.25 mm for a 45° blade, 0.5 mm for 60°): Bernie swivels the blade around each corner, for sharp corners. Overcut (1 mm by default): the start of closed shapes is cut again, so they come off. On a GRBL machine, the knife is lifted like a pen (servo or Z axis). Prefer Line mode: a fill would be cut line by line (the pre-send check warns about it).
- Laser panel of an HPGL cutter (Mac, Windows and Linux desktop app): the cutter’s serial port, port speed and flow control (software XON/XOFF, hardware RTS/CTS, or none) — those of the machine, often 9600 baud. Test the link asks the cutter for its model, without moving anything (many do not answer, which does not mean the link is at fault). Send to the cutter: it starts as soon as it receives the job — load the material, check the blade and the origin; Stop sending does not clear its memory, it finishes what it has already received. Virtual cutter (test without a machine): the job goes to an imaginary cutter, which reports what it received. On Linux, the serial port requires the
dialoutgroup (Bernie gives the command). - HPGL file (.plt): Laser panel, or File › Export as HPGL (.plt) (Bernie Studio: File › Export › HPGL) — to send it with other software; it is the output on iPad, iPhone and Bernie Studio in a browser. 40 units per millimetre, in the device’s coordinates (origin, swapped X and Y), tool up
PUand downPD. - Speed: that of each layer (mm/s; 100 mm/s gives
VS10, in cm/s). The blade pressure is set on the cutter. - Silhouette (Cameo 1 to 5, Cameo 4 Plus and Pro, Pro MK-II, Cameo 5 Alpha, Portrait 1 to 4; Mac, Windows and Linux desktop app): over USB, without Silhouette Studio. Laser panel: Connected Silhouette (recognized with its model), Model, Blade pressure (1 to 33: vinyl 8 to 12, cardstock 25 to 33), layer speed (cm/s, up to 10 or 30 depending on the model); Test the link reads the machine’s name and version; Send to the Silhouette — load the mat or the sheet first. The Silhouette corrects the blade itself; Bernie adds the overcut of closed shapes. Starting area: the 12 × 12 inch mat, origin top left. On Windows, the Silhouette must use the WinUSB driver (Zadig tool, instead of the printer driver); on Linux, the USB access rule is installed by Bernie’s packages. Close Silhouette Studio before sending. Virtual Silhouette to try without a machine. Not yet on iPad, iPhone or in a browser.
- HPGL cutter connection (Laser panel, Link): Serial port; Network (Ethernet, Wi-Fi) — the machine’s IP address and port, 9100 for most (Roland GR2 and GS2-24, Summa, GCC): the job is sent as is, from the iPad and iPhone too; USB — printer-class cutters (Roland, Summa in “Printer” mode…), no driver needed, on Mac and Linux (access rule installed by Bernie’s packages); Windows printer — the cutter as installed by its maker’s driver (Roland…), which receives the HPGL as is. Roland, Graphtec, Summa… correct the blade themselves: set Blade offset to 0 in the device settings. The GR2-540 speaks HP-GL; a GS-24 or GX-24 reads HP-GL in CAMM-GL III mode 2.
- Brother ScanNCut (CM, SDX and DX series): at “Your machine”, Controller: Brother ScanNCut (file on a USB stick). Laser panel: Mat (12 × 12 or 12 × 24 in, the work area follows) and File for the ScanNCut (.fcm)… (also File › Export); copy the file to the root of a USB stick, plug it into the machine and retrieve it from its screen; a ScanNCut CM connected by its USB cable also shows up as a drive. One pattern in place on the mat (origin top left), one stroke per shape, with the blade or the pen depending on the device’s tool; the ScanNCut corrects the blade itself, and thickness, pressure and speed are set on the machine. Files written from the public description of the FCM format, not yet tried on every machine: make a small test cut first.
This manual is also built into Bernie: press F1, or open the Help menu, to read the topic for what you are doing. A mistake, a missing answer? Tell us
Try it in Bernie, for free.
Free laser engraving and cutting software for diode, CO2, fiber and galvo lasers. Windows, Mac, Linux, iPad, iPhone and in the browser.