Compatibility
The laser engravers compatible with Bernie.
Look for your machine: each model below has a ready-made profile in Bernie, with its work area, port speed and macros. Not listed? The controller matters more than the brand, and the answer is further down the page.
125 machines
17 brands
8 controller families
All machines, by brand
List up to date for Bernie 2.0.7. The real travel is read back when you connect and Bernie offers to align the profile, so these work areas are a starting point. App store versions get new machines with their next update.
- Direct control
- Bernie frames, sends and follows the job.
- File preparation
- Bernie prepares the job at the right size but does not drive the machine.
125 machines
Acmer lasers
3 machines
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Acmer S1 | 130 × 130 mm | Diode | GRBL | Direct control |
| Acmer P3 (24 W) | 400 × 400 mm | Diode | GRBL | Direct control |
| Acmer P3 (48 W, dual laser) | 400 × 390 mm | Diode | GRBL | Direct control |
Atomstack lasers
42 machines
The whole range, older models included, in GRBL over USB: 115,200 baud up to the 2024 models, 460,800 baud for the P1, Swift, Kraft, Glacier and Hurricane. Wi-Fi on recent models is for AtomStack’s app. The P1 is unlocked by its USB safety key, plugged into the machine.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Atomstack A5 (20 W, 30 W) | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A5 M30, A5 M40 | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A5 Pro (40 W) | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A5 Pro+, A5 M50 | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A6 Pro | 365 × 305 mm | Diode | GRBL | Direct control |
| Atomstack A10 Pro | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A10 Pro V2 | 400 × 365 mm | Diode | GRBL | Direct control |
| Atomstack A12 Pro | 365 × 305 mm | Diode | GRBL | Direct control |
| Atomstack A20 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A20 Pro V2 | 400 × 365 mm | Diode | GRBL | Direct control |
| Atomstack A20 Pro (1064 nm fiber) | 400 × 400 mm | Infrared | GRBL | Direct control |
| Atomstack A20 Max | 850 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A24 Pro | 365 × 305 mm | Diode | GRBL | Direct control |
| Atomstack A24 Pro (1064 nm fiber) | 365 × 305 mm | Infrared | GRBL | Direct control |
| Atomstack A30 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A40 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A40 Pro V2 | 385 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A40 Max | 800 × 400 mm | Diode | GRBL | Direct control |
| Atomstack A70 Max | 850 × 800 mm | Diode | GRBL | Direct control |
| Atomstack A70 Pro | 400 × 500 mm | Diode | GRBL | Direct control |
| Atomstack P7 M30, P7 M40 | 200 × 200 mm | Diode | GRBL | Direct control |
| Atomstack P9 M40, P9 M50 | 220 × 250 mm | Diode | GRBL | Direct control |
| Atomstack S10 Pro | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack S20 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack S30 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack S40 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack X7 Pro | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack X12 Pro | 365 × 305 mm | Diode | GRBL | Direct control |
| Atomstack X20 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack X24 Pro | 365 × 305 mm | Diode | GRBL | Direct control |
| Atomstack X30 Pro | 410 × 400 mm | Diode | GRBL | Direct control |
| Atomstack X40 Pro | 400 × 400 mm | Diode | GRBL | Direct control |
| Atomstack X40 Max | 800 × 400 mm | Diode | GRBL | Direct control |
| Atomstack X70 Max | 850 × 800 mm | Diode | GRBL | Direct control |
| Atomstack P1 (5 W) | 110 × 110 mm | Diode | GRBL | Direct control |
| Atomstack P1 Dual (5 W + 1.2 W infrared) | 110 × 110 mm | Diode + IR | GRBL | Direct control |
| Atomstack Swift (7 W, 12 W) | 300 × 300 mm | Diode | GRBL | Direct control |
| Atomstack Swift Mini | 135 × 145 mm | Diode | GRBL | Direct control |
| Atomstack Kraft Dual (20 W + 1.2 W infrared) | 500 × 320 mm | Diode + IR | GRBL | Direct control |
| Atomstack Kraft Lite (40 W) | 500 × 320 mm | Diode | GRBL | Direct control |
| Atomstack Glacier (90 W, 120 W) | 800 × 800 mm | Diode | GRBL | Direct control |
| Atomstack Hurricane (CO2 55 W) | 500 × 300 mm | CO2 | GRBL | Direct control |
BlazeX lasers
3 machines
Driven in GRBL over USB; Wi-Fi is for the manufacturer’s app. With the enclosure fitted, the machine only connects with the lid closed. Bernie picks the material settings from the head’s power.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| BlazeX M2 Pro (20 W) | 300 × 300 mm | Diode | GRBL | Direct control |
| BlazeX M3, M3 Pro (10 W) | 200 × 150 mm | Diode | GRBL | Direct control |
| BlazeX M3, M3 Pro (3 W, 5 W) | 200 × 150 mm | Diode | GRBL | Direct control |
Creality lasers
5 machines
The Falcon A1 gets air assist (M8) on every layer.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Creality CR-Laser Falcon 10W | 400 × 415 mm | Diode | GRBL | Direct control |
| Creality Falcon A1 | 381 × 305 mm | Diode | GRBL | Direct control |
| Creality Falcon A1 Pro | 358 × 268 mm | Diode | GRBL | Direct control |
| Creality Falcon2 Pro (22 W, 40 W) | 400 × 415 mm | Diode | GRBL | Direct control |
| Creality Falcon2 22W | 400 × 415 mm | Diode | GRBL | Direct control |
Emblaser lasers
4 machines
Emblaser machines have their own protocol, which Bernie does not drive: the profile is used to prepare jobs at the right size.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Emblaser 1 A3 | 419 × 287 mm | Diode | Own protocol | File preparation |
| Emblaser 1 A4 | 305 × 210 mm | Diode | Own protocol | File preparation |
| Emblaser 2 / Core | 500 × 300 mm | Diode | Own protocol | File preparation |
| Emblaser 3 | Set in the profile | Diode | Own protocol | File preparation |
Gweike lasers
4 machines
The Cloud, Cloud Pro, Cloud Basic II and Cloud Pro II (50 and 55 W) are driven through the USB port of their Ruida controller, on Mac, Windows and Linux, or through Bernie Link on a Raspberry Pi plugged into the machine, from Bernie Studio in the browser. The machine’s network is for its camera and Gweike’s app.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Gweike Cloud (50 W) | 510 × 300 mm | CO2 | Ruida | Direct control |
| Gweike Cloud Pro (50 W) | 510 × 300 mm | CO2 | Ruida | Direct control |
| Gweike Cloud Basic II (50 W) | 510 × 300 mm | CO2 | Ruida | Direct control |
| Gweike Cloud Pro II (50 W, 55 W) | 510 × 300 mm | CO2 | Ruida | Direct control |
K40 lasers
2 machines
With its stock M2 Nano board, Bernie drives the K40 directly, with no board upgrade. With a replacement board, such as a DLC32 or running FluidNC, it speaks GRBL. See the K40 guide.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| K40 CO2 40 W (M2 Nano) | 300 × 200 mm | CO2 | M2 Nano | Direct control |
| K40 CO2 40 W (GRBL, FluidNC, DLC32) | 300 × 200 mm | CO2 | GRBL | Direct control |
LaserPecker lasers
5 machines
Driven in G-code over USB, with the manufacturer’s macros (red dots, electric stand, extensions). The LP4 comes with its two heads, diode (450 nm) and infrared (1,064 nm), chosen by each layer. The LP1, LP2, LP3 and LP5 only speak the protocol of their app: Bernie does not drive them.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| LaserPecker LP2 Plus | 100 × 100 mm | Diode | GRBL | Direct control |
| LaserPecker LP4 | 160 × 120 mm | Diode + IR galvo | GRBL | Direct control |
| LaserPecker LX1 | 400 × 420 mm | Diode | GRBL | Direct control |
| LaserPecker LX1 Max | 400 × 800 mm | Diode | GRBL | Direct control |
| LaserPecker LX2 | 500 × 305 mm | Diode + IR | GRBL | Direct control |
Longer lasers
3 machines
The Nano is a diode galvo running GRBL, over USB or Wi-Fi.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Longer Ray5 (5 W, 10 W) | 400 × 400 mm | Diode | GRBL | Direct control |
| Longer Ray5 20W | 400 × 365 mm | Diode | GRBL | Direct control |
| Longer Nano Pro (12 W), Nano (6 W) | 100 × 100 mm | Diode galvo | GRBL | Direct control |
Makera lasers
1 machine
The Carvera Air with its 5 W laser module, running Smoothieware: Bernie switches the machine to laser mode at the start of the job.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Makera Carvera Air (laser module) | 300 × 200 mm | Diode | Smoothieware | Direct control |
Mecpow lasers
6 machines
Makerbase board driven in GRBL over USB. Bernie picks the material settings from the module’s power.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Mecpow X3 (5 W) | 410 × 400 mm | Diode | GRBL | Direct control |
| Mecpow X4 (22 W) | 410 × 400 mm | Diode | GRBL | Direct control |
| Mecpow X4 Pro (22 W) | 410 × 400 mm | Diode | GRBL | Direct control |
| Mecpow X4 Pro (40 W) | 400 × 398 mm | Diode | GRBL | Direct control |
| Mecpow X5 (22 W) | 600 × 600 mm | Diode | GRBL | Direct control |
| Mecpow X5 Pro (33 W) | 600 × 600 mm | Diode | GRBL | Direct control |
NEJE lasers
1 machine
The Master 3 Max has two firmwares, NEJE and GRBL: Bernie uses GRBL.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| NEJE Master 3 Max | 810 × 460 mm | Diode | GRBL | Direct control |
Ortur & Aufero lasers
19 machines
The whole range, older models included, over USB at 115,200 baud. Bernie reads the model name from the controller. On the Laser Master 3, H20, R1 and R2, pick the line for your module: the work area depends on it. The F10 is a conveyor: its length is that of the material it feeds.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Ortur Laser Master 1 | 150 × 160 mm | Diode | GRBL | Direct control |
| Ortur Laser Master 2 | 400 × 430 mm | Diode | GRBL | Direct control |
| Ortur Laser Master 2 S2 | 390 × 410 mm | Diode | GRBL | Direct control |
| Ortur Laser Master 2 Pro (S1, S2) | 400 × 400 mm | Diode | GRBL | Direct control |
| Ortur Laser Master 3 (10 W) | 400 × 400 mm | Diode | GRBL | Direct control |
| Ortur Laser Master 3 (20 W, 40 W) | 400 × 380 mm | Diode | GRBL | Direct control |
| Ortur Laser Master 3 LE | 400 × 400 mm | Diode | GRBL | Direct control |
| Ortur Laser Master H10 | 300 × 300 mm | Diode | GRBL | Direct control |
| Ortur H20 (10 W, 20 W) | 420 × 300 mm | Diode | GRBL | Direct control |
| Ortur H20 (40 W) | 410 × 275 mm | Diode | GRBL | Direct control |
| Ortur H20 (IR 2 W) | 420 × 275 mm | Infrared | GRBL | Direct control |
| Ortur F10 | 400 × 3,000 mm | Diode | GRBL | Direct control |
| Ortur R1 (5 W) | 100 × 100 mm | Diode | GRBL | Direct control |
| Ortur R1 (IR 1.3 W) | 100 × 80 mm | Infrared | GRBL | Direct control |
| Ortur R2 (10 W, IR 1.3 W) | 300 × 210 mm | Diode + IR | GRBL | Direct control |
| Ortur R2 (20 W) | 300 × 190 mm | Diode | GRBL | Direct control |
| Ortur Aufero Laser 1 (AL1) | 180 × 180 mm | Diode | GRBL | Direct control |
| Ortur Aufero Laser 2 (AL2) | 390 × 390 mm | Diode | GRBL | Direct control |
| Ortur Aufero Laser 3 (AL3) | 400 × 400 mm | Diode | GRBL | Direct control |
Sculpfun lasers
8 machines
Driven in GRBL over USB. A Sculpfun missing from the list is set up like any GRBL machine, with Find My Laser or Custom Machine.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Sculpfun C1 | 150 × 130 mm | Diode | GRBL | Direct control |
| Sculpfun iCube (3 W, Pro 5 W) | 125 × 125 mm | Diode | GRBL | Direct control |
| Sculpfun iCube Ultra | 150 × 150 mm | Diode | GRBL | Direct control |
| Sculpfun S9 | 410 × 400 mm | Diode | GRBL | Direct control |
| Sculpfun S30 / S30 Pro | 380 × 385 mm | Diode | GRBL | Direct control |
| Sculpfun S30 Pro Max | 370 × 360 mm | Diode | GRBL | Direct control |
| Sculpfun S40 MAX | 830 × 800 mm | Diode | GRBL | Direct control |
| Sculpfun S70 MAX | 830 × 800 mm | Diode | GRBL | Direct control |
Snapmaker lasers
4 machines
The Ray has its own material library, for its 20 W and 40 W modules.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| Snapmaker 2.0 A250T | 250 × 250 mm | Diode | GRBL | Direct control |
| Snapmaker 2.0 A350T | 350 × 350 mm | Diode | GRBL | Direct control |
| Snapmaker Artisan | 400 × 400 mm | Diode | GRBL | Direct control |
| Snapmaker Ray | 600 × 400 mm | Diode | GRBL | Direct control |
TwoTrees lasers
1 machine
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| TwoTrees TTS-55 Pro | 300 × 300 mm | Diode | GRBL | Direct control |
WorldStarTech lasers
1 machine
A MOPA fiber source driven in custom G-code, with frequency and pulse width. Set the work area in the profile.
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| WorldStarTech MOPA (G-code) | Set in the profile | MOPA fiber | G-code | Direct control |
xTool lasers
13 machines
The D1, D1 Pro, D1 Pro 2.0 and S1 are driven over USB or Wi-Fi; the M1, M1 Ultra, P2, P2S, F1, F1 Lite, F1 Ultra and F2 Ultra over Wi-Fi or their USB cable. Over the network, Bernie speaks xTool’s protocol, on Mac, iPad, iPhone, Windows and Linux (not in the browser). The S1 and M1 start from the button on the machine. The D1 Pro has its own material library, and Bernie opens xTool Creative Space projects (.xcs).
| Model | Work area | Laser | Controller | Support |
|---|---|---|---|---|
| xTool D1 (5 W, 10 W) | 432 × 406 mm | Diode | GRBL | Direct control |
| xTool D1 Pro (5 W, 10 W) | 430 × 400 mm | Diode | GRBL | Direct control |
| xTool D1 Pro 20 W | 430 × 390 mm | Diode | GRBL | Direct control |
| xTool D1 Pro 2.0 (10 W, 20 W, 40 W) | 430 × 390 mm | Diode | GRBL | Direct control |
| xTool S1 (10 W, 20 W, 40 W) | 498 × 319 mm | Diode | GRBL | Direct control |
| xTool M1 (10 W, 20 W) | 385 × 300 mm | Diode | xTool | Direct control |
| xTool M1 Ultra | 300 × 300 mm | Diode | xTool | Direct control |
| xTool P2 (CO2 55 W) | 600 × 305 mm | CO2 | xTool | Direct control |
| xTool P2S (CO2 55 W) | 600 × 305 mm | CO2 | xTool | Direct control |
| xTool F1 (galvo) | 115 × 115 mm | Diode + IR galvo | xTool | Direct control |
| xTool F1 Lite (galvo) | 115 × 115 mm | Diode galvo | xTool | Direct control |
| xTool F1 Ultra (galvo) | 220 × 220 mm | Fiber + diode galvo | xTool | Direct control |
| xTool F2 Ultra (galvo) | 220 × 220 mm | Fiber + diode galvo | xTool | Direct control |
No machine matches your search. What to do if your laser is not listed
Your laser is not in the list?
The list only covers ready-made profiles. Beyond that, the controller decides: here are three ways to set up your machine.
01
Find My Laser
Plug it in: Bernie tries the usual speeds, reads the work area, power, speeds and accelerations from the controller, and creates the profile.
02
Custom Machine
In the assistant, pick the controller and enter the work area: that is all a laser outside the catalog needs.
03
Import a profile
A .lbdev device profile or a Bernie profile brings back your settings and macros; Bernie points out anything with no equivalent.
By controller
Direct control
- GRBL, grblHAL, FluidNC, GRBL-M3
- Marlin
- Smoothieware
- Duet / RepRapFirmware, Mach3 / Mach4, UCCNC (custom G-code)
- OctoPrint and Duet, over the network
- Ruida, over USB and the network, dual tube included
- JCZ “LMC” galvo boards (EZCad2), over USB
- K40 Lihuiyu boards (M2 Nano, M3, B2…)
- xTool, over the network (Wi-Fi or USB cable)
- HPGL and Silhouette cutters
File preparation
- Trocen, TopWisdom
- EZCad3 “DLC” and BSL galvo boards
- Brother ScanNCut (.fcm file)
- Emblaser’s own protocol
Fiber galvo lasers
Most fiber galvo lasers sold from China have a JCZ “LMC” board, the EZCad2 one (USB ID 9588:9899, “USBLMCV4”): Bernie drives it directly, without EZCad.
Over USB, everywhere
The Mac app, with nothing to install; the Windows desktop app (WinUSB driver installed with Zadig in place of the EZCad one) and Linux; Bernie Studio in Chrome or Edge; the iPad and iPhone, through Bernie Link.
Fiber and MOPA sources
Q-switched and MOPA sources (JPT M7, Raycus…), with frequency and pulse width set layer by layer; UV and CO2 galvo too.
EZCad configuration
Import of the EZCad2 markcfg file (field size and offset, mirrors, scales, lens corrections, frequencies) and of the EZCad3 Motors.ini.
Frame, mark, stop
Framing with the red pointer, which follows the design; marking after a safety question; immediate stop at any time.
Other boards
EZCad3 “DLC” boards and BSL boards are not driven directly: Bernie prepares the job and exports it (SVG, DXF, or .ezd for EZCad2).
Vinyl cutters and plotters
Bernie also drives cutters (adhesive vinyl, heat transfer vinyl, paper) and pen plotters, with no internet connection: a Knife tool (blade offset corrected in the corners, overcut on closed shapes), a starter library for the cutter and HPGL (.plt) files everywhere. Cricut machines, with their closed protocol, are not supported.
HPGL cutters
Roland GR2 and GS2-24, Summa, GCC… over the serial port, over the network (IP address, port 9100, from the iPad and iPhone too), over printer-class USB with no driver (Mac, Linux) or through the Windows printer installed by the maker’s driver.
Silhouette
Cameo 1 to 5 and Portrait 1 to 4, over USB, without Silhouette Studio: on Mac, Windows (with the WinUSB driver) and Linux.
Brother ScanNCut
CM, SDX and DX series: Bernie writes an .fcm file, on the 12 × 12 or 12 × 24 inch mat, to copy to a USB stick; the machine cuts it from its screen.
Plotters and GRBL machines
A pen or a knife on a GRBL machine, lifted by a servo or the Z axis: pen plotters and home-made machines.
Compatibility questions
How do I know if my laser works with Bernie?
Look for it in the list above. If it is not there, check its controller in the documentation or on the board label: GRBL, grblHAL, FluidNC, Marlin and Smoothieware are driven directly. You can also plug it in and run Find My Laser: Bernie is free, so trying costs nothing.
Does Bernie work with xTool lasers?
Yes. Bernie drives the M1, M1 Ultra, P2, P2S, F1, F1 Lite, F1 Ultra and F2 Ultra over Wi-Fi or their USB cable, and the D1, D1 Pro, D1 Pro 2.0 and S1 over Wi-Fi or USB, on Mac, Windows and Linux, and over Wi-Fi on iPad and iPhone. In the browser, Bernie Studio drives the D1 and D1 Pro over USB. It also opens xTool Creative Space projects (.xcs).
Does Bernie drive fiber galvo lasers?
Yes, those with a JCZ “LMC” board from EZCad2, the most common one: over USB on Mac, Windows and Linux, in Chrome or Edge with Bernie Studio, and from the iPad and iPhone through Bernie Link. EZCad3 “DLC” boards are not driven directly.
Does Bernie drive vinyl cutters?
Yes: HPGL cutters (Roland, Summa, GCC…) over the serial port, the network or USB, Silhouette Cameo and Portrait over USB, and Brother ScanNCut through a file on a USB stick. Cricut machines, with their closed protocol, are not.
Does Bernie work with a K40?
Yes, in two ways. With the stock M2 Nano board, Bernie drives it directly, with no board upgrade. With a replacement board, such as a DLC32 or running FluidNC, it speaks GRBL. The K40 guide explains everything.
Can I use these lasers from an iPad, an iPhone or a browser?
USB lasers are driven from a Mac, Windows and Linux, and in Chrome or Edge with Bernie Studio. The iPad and iPhone have no USB port for a laser: they reach network lasers directly, and USB lasers through Bernie Link or a Mac in Hub mode. The download page compares every platform.
Why does my machine have a different work area?
The work area changes with the laser module and extension kits. On a GRBL machine, Bernie reads the real travel when you connect and offers to align the profile; you can also change it in the profile at any time.
How do I ask for a machine to be added?
Tell us the model on the ideas page. The list grows with each version of Bernie.
Try it with your laser.
Bernie is free, with no account. Install it, plug in the machine, and the assistant does the rest.